3-Cup Action Camera Suction Cup Mount Motion Camcorder Car Windshield Hood Door Trunk Lid Holder/w Ball Head Compatible with GoPro Sony DJI OSMO A...

Having three suction cups gives me a little more confidence when mounting my GoPro camera on the outside of my car.

VERY STURDY held on no issues at all , A lot of people mount it to the panels of the car which might be why it falls off for some , I put it on the windows and it held on great going 70+ on the highway, just clean the glass before you mount it , also don't use the ball mount that it comes with it's not very sturdy and you'll probably end up loosing your camera has broken according to many other reviews , use the smaller ones and make a 90. Degree one for good angles !

Garbage. Went to the drag strip with some friends racing their semis. Top speed under 80mph. The suction cups work great. Unfortunately the rest of the plastic is garbage. The whole mount broke on one of the runs, causing my gopro to fall of, and the get run over. I'm out $400 because I thought that a 3 cup amount would be better than the gopro single. I was wrong.

This is a very limited use review as I only received it today and did some very quick testing to attach to the side of my car. Before ordering I asked the question of whether or not I would be able to replace the very flimsy looking ball head that comes with it, with another ball head and received the reply that yes I would be able to do that. With that in mind I did place the order and when I received it today I double checked to make certain that that is in fact correct and am happy to say that it is. As a matter of fact, it comes somewhat disassembled so that you have to install the included ball head. It uses a standard 1/4 inch screw, which is the same size as the one that goes into the bottom of your camera. Looking at the ball head that comes with it which is made 100% of plastic except for the threads that the head attaches to the base with and the screw that goes into the camera, it really looks flimsy to me, even for something as light as an action camera, such as the GoPro, or for a cell phone. I immediately went to ZeeBooth and ordered a much more substantial metal ball head for around $7 (well, at least substantial compared to the flimsy plastic one that came with it). Even with the better head I'll still tether the camera to any moving vehicle if I have it on the outside. The reason I ordered the better head instead of sending the whole unit back is because the base with the suction cups seems to be quite solid and capable. I like the design of the base unit with the three suction cups which can be angled up and down to fit different contours a little better. The screws and nuts that hold the suction cups to the main base appear to be a light metal. Also the pins on the cams that draw the suction plastic up to get a secure hold are metal, though everything else is plastic. After cleaning off the side of my car with a wet cloth and then wiping the suction cups with that same wet cloth I mounted the holder to the side of the car and tried to pull it off. I put probably a hundred times more pressure on it than the camera ever will and it didn't budge. However . . . considering that I may be driving on rough roads/trails etc, I don't know what the dust, vibration and other physics may do to work it loose, so, as I mentioned before I will never put the camera on a moving vehicle without being tethered with a length of tether that will not allow the camera to hit the ground if it comes loose for any reason. If you are looking for something to mount for this type of application and you are only going to mount a very light camera, I think this would do the trick nicely for you and at a very economical price. As mentioned above, however, I would strongly recommend spending another $8 to $10 and get a ball head that is mostly if not entirely metal. Make sure it has a 1/4 inch mounting screw hole in the base, NOT a 3/8 inch like the more heavy duty ones use. Obviously the attached photo is with the very light duty included ball head as I have not received the new one I ordered yet. I will update if anything changes.

Easy to use, my concern doing film clips was will it stay on? well after testing in down pouring rain multiple times and on Highway at 65mph+ not one issue. They stayed in place, even for events where I had them mounted to other vehicles no issue at all. If wondering if they will hold up, no need to wonder they work amazingly!